Manual isobaric keg filler, S type head Kegland
Code: HB-KB23834Related products
Product detailed description
The procedure of filling of the keg using the filling head :
- Sterilize both the coupler and the filling connector on the keg using some sanitizing solution with alcohol.
- Connect the filling head using the bottom connector onto the keg.
- Close the valves No 1 and 3.
- Open the valve No 2 and fill pressure CO2 gas into the keg. We recommend to set the pressure in the keg lower than is the pressure in the source tank.
- Check the pressure on manometer during the filling process.
- Close the valve No 2 when you reach the target pressure in the keg.
- Open the valve for beverage input No 1. At the same time slightly open the valve No 3 and let release the CO2 out from the keg. The pressure in the keg rises during the filling.
- Slowly open the valve No 3. When the beverage with foam leaks out then the keg is full.
- Close all valves at this moment and disconnect the coupler from the keg. The keg is full now.
- Disconnect the filling head from the keg.
Filling of the 50-liters keg takes from 1 up to 4 minutes – the time depends on the chosen overpressure and beer type.
Sent dismantled.
Additional parameters
| Category: | Keg and Bottle Fillers |
|---|---|
| Sada: | HB-KL00406`1`https://www.bahnik.cz/kulovy-kohout-5-8-f-m-nerez/`https://cdn.myshoptet.com/usr/www.bahnik.cz/user/shop/orig/829_hb-1207-nerozovy-kulovy-kohout-ball-valve-f5-8xm5-8-ss-22.jpg?6336b51b`Kulový kohout 5/8 F/M nerez¨SPO00923`1`https://www.bahnik.cz/rs-f5-8x9-5mm-dmfit/`https://cdn.myshoptet.com/usr/www.bahnik.cz/user/shop/orig/268-4_spo00923-dm-afab0608f-rychlospojka-f1-2x9-5mm.jpg?6336b51b`RS F5/8x9,5mm DMfit¨SPO00935`2`https://www.bahnik.cz/rs-f5-8x8mm-dmfit/`https://cdn.myshoptet.com/usr/www.bahnik.cz/user/shop/orig/139-2_spo00935-dm-afab0508f-rychlospojka-f5-8x8mm.jpg?6336b51b`RS F5/8x8mm DMfit¨RED01862`2`https://www.bahnik.cz/red--kulovy-kohout-1-4x5-8-m-m-mosaz/`https://cdn.myshoptet.com/usr/www.bahnik.cz/user/shop/orig/1798_redukcni-ventil-kohout-1-st-.jpg?6336b51b`Red. kulový kohout 1/4x5/8 M/M mosaz¨SPO1415`1`https://www.bahnik.cz/adapter-f5-8xm1-4/`https://cdn.myshoptet.com/usr/www.bahnik.cz/user/shop/orig/6859_adapter-f5-8xm1-4.jpg?65cb7a10`Adaptér F5/8xM1/4¨SPO1257`1`https://www.bahnik.cz/nerezova-spojka-t-1-2/`https://cdn.myshoptet.com/usr/www.bahnik.cz/user/shop/orig/6862-2_spojka-1-4.jpg?65cb741b`Spojka "+" F1/4¨HB-KL10888`1`https://www.bahnik.cz/teflonova-paska-19mm-x-15m-x-0-2mm/`https://cdn.myshoptet.com/usr/www.bahnik.cz/user/shop/orig/400_kl10888-teflonova-paska.jpg?6336b51b`Teflonová páska 19mm x 15m x 0.2mm¨HB-KL08839`1`https://www.bahnik.cz/narazec-bajonet--s-type--nerez/`https://cdn.myshoptet.com/usr/www.bahnik.cz/user/shop/orig/5926-2_narazec-bajonet-nerez-s-type-kegland.jpg?65ddf22e`Naražeč BAJONET KL (S-type) SS¨HB-KL11532`1`https://www.bahnik.cz/manometr-0-10-bar-s-vsuvkou-8mm/`https://cdn.myshoptet.com/usr/www.bahnik.cz/user/shop/orig/5959_kl11532-manometr-se-vsuvkou-0-10bar.jpg?63ee3212`Manometr se vsuvkou 8mm 0-10 bar¨SPO01337`1`https://www.bahnik.cz/rs-m1-4x8mm--5-16-bsp-dmfit-o-krouzek/`https://cdn.myshoptet.com/usr/www.bahnik.cz/user/shop/orig/148-1_spo01337-dm-amcb0804m-rychlospojka-m1-4x5-16.jpg?633be078`RS M1/4x8mm (5/16") DMfit O-kroužek |
5,0
1 rating
Add a rating
5
4
3
2
1
5
R
Radegast24
Radegast24
Objednány jednotlivé díly (bez narážeče, mám 2x bajonet), sestaveno, stočeno prvních 15 litrů. Počáteční neduhy byly odstraněny, chyba zřejmě na mé straně. Utěsněno teflonovou páskou, kromě kulového ventilu na nápoj, který má gumové těsnění, to ovšem lehce prosakovalo. Vzhledem k tomu, že jsem stáčel piwko z velkého KEGu do 5 litrových KEGů (https://www.bahnik.cz/minikeg-5l-bajonet/), naprostá spokojenost. U narážeče je nutné vyjmout retní ventil a "zpětnou kuličku" nápoje.
Be the first who will post an article to this item!